#contents
----
*Creating FuguIta Media (on OpenBSD, for example) [#dbef1e2f]
**Creating LiveDVD [#qd9ded45]
-Install DVD writing tool
 # pkg_add dvd+rw-tools
-Download the ISO image of FuguIta from the site described in [[FuguIta/Download]].
 # ftp http://mirror-of-fuguita/FuguIta-6.X-20YYMMDDN.iso.gz
Note that the part ''YYMMDDN'' must be replaced with the version string of real ISO image.
-After decompression completed, burn that image into DVD-R or DVD-RW.
 # gzip -d FuguIta-6.X-20YYMMDDN.iso.gz
 # dvd-format /dev/rcd0c    (format media, if you will be burn it first)
 # growisofs --dvd-compt -Z /dev/rcd0c=FuguIta-6.X-20YYMMDDN.iso

**Creating LiveUSB [#h1779af1]
To make a LiveUSB version of FuguIta, prepare a USB memory with a size of 2 gigabytes or more, and write the downloaded and expanded IMG format file.
The following is an example of writing using OpenBSD.
>
-Download the image for USB flash drive
 # ftp http://livecd-mirror.ebug.jp/LiveDVD/FuguIta-6.X-20YYMMDDN.img.gz
-Decompressing that image, and write it into USB storage device.
 # gzip -dc FuguIta-6.X-20YYMMDDN.img.gz | dd of=/dev/rsd?c bs=1m
The "/dev/rsd0c" part in the above example is the designation of the write destination device. This depends on the connection status of the peripherals of your PC. If you execute this command, all the data recorded in the specified device will be erased, so be sure to check in advance if the write destination is correct.

Even if you use a USB memory of 2 GB or more, the portion exceeding 2 GB will not be used.
If you want to create a LiveUSB version FuguIta that matches the size of the USB memory, refer to "Remastering LiveUSB from running FuguIta".

*Booting FuguIta [#rba5c27f]
After booting from DVD/USB,
some user inputs will be prompted;
 disks: *cd0a fd0 fd1 rd0 sd0
 Disk to boot FuguIta? [cd0a] ->
'*' means the device which stores FuguIta system
   user memory: 267927552 bytes
 mfs available: 10MB to 255MB
 [default: 127MB] -> 
Only entering "ENTER", half amount of attached memory is specified by default.
 set mfs size to default: 127MB
Choose the way of boot
 Select boot mode;
   0: fresh boot (normal)
   1: fresh boot (lower memory, faster boot than mode 0)
   2: fresh boot (everything on mfs)
   3: retrieve user data from USB flash memory
   4: retrieve user data from floppy disk
   5: interactive shell for debugging
 ->0
:0 normal fresh boot mode|Like booting just after fresh install. Some parameters are needed to be entered manually. This is the standard fresh boot method.
:1 fresh boot with faster and less memory|Same as above. ~
But under /usr, all files and directories are ''read only''.
:2 ''everything on mfs'' mode (i.e. diskless mode)|Same as mode 0. ~
All files and directories will have copied on mfs. This mode requires about more than 650--700MB RAM.
:3 Restoring user data from USB flashdrive|After DVD/USB boot, extract files which were stored in USB flash. (to be more described)
:4 Restoring user data from floppy disk|Same as above, but extracting from floppy disk. (to be more described)
:5 Interactive shell mode|After DVD/USB boot, single user shell invoked. This is intended for system debug.

At first, you should enter mode 0 (recommended) or mode 1.
 Running manual setup.
 Copying system files to /mfs ... done
 Extracting symlinks from /mfs to /fuguita ... done
Choose keyboard type
 Keyboard type;
 be      be.swapctrlcaps br      cf
 cf.nodead       de      de.nodead       dk
 dk.nodead       es      fr      fr.dvorak
 fr.swapctrlcaps fr.swapctrlcaps.dvorak  hu      it
 jp      jp.swapctrlcaps la      lt
 lv      nl      nl.nodead       no
 no.nodead       pl      pt      ru
 sf      sf.nodead       sg      sg.nodead
 si      sv      sv.nodead       tr
 tr.nodead       ua      uk      us
 us.declk        us.dvorak       us.iopener      us.swapctrlcaps
 us.swapctrlcaps.dvorak  us.swapctrlcaps.iopener
 -> us
Enter root password twice
 Please wait.....
 Changing local password for root.
 New password:
 Retype new password:
Setting network parameters.
 host name (without domain) -> nimbus5
 
 IP version(s) to use [n, 4, 6 or 46]-> 46
 
 ==[ifconfig -a]=========================
 lo0: flags=8008<LOOPBACK,MULTICAST> mtu 33200
         priority: 0
         groups: lo
 ne3: flags=8822<BROADCAST,NOTRAILERS,SIMPLEX,MULTICAST> mtu 1500
         lladdr 52:54:00:12:34:56
         priority: 0
         media: Ethernet 10baseT full-duplex
 enc0: flags=0<> mtu 1536
         priority: 0
 ========================================
 Available network interface(s): ne3
 network interface to setup [ne3] -> 
 
 FQDN of this host -> nimbus5.localnet
 
 for DNS servers;
  * up to three IPv4/IPv6 addresses, separated by spaces
  * just press ENTER for DHCP
  * "none" for not using DNS
 -> 192.168.18.254
 
 IPv4 addr of this host -> 192.168.18.25
 netmask                -> 255.255.255.0
 default route          -> 192.168.18.254
In above case;
-IPv4 was configured manually.
-IPv6 was set up as end node by automatic stateless configuration.

...then you will see a login prompt.
 Generation of SSH and isakmpd keys take some time while booting.
 ========================================
 Automatic boot in progress: starting file system checks.
 setting tty flags
 kbd: keyboard mapping set to us
 pf enabled
....snip....
 starting network daemons: sshd rtsold sendmail inetd.
 starting local daemons:.
 standard daemons: cron.
 Sat May 29 06:19:13 JST 2010
 
 OpenBSD/i386 (nimbus5.localnet) (tty00)
 
 login: 

* Remastering LiveUSB from running FuguIta [#q4366f48]
By this procedure, the data partition will be automatically allocated. ~
Also, you can specify its size.
>
-First, create FuguIta LiveDVD or LiveUSB from download file, then run it.
-Login as root, then execute ''newdrive'' subcommand on the USB management tool ''usbfadm''.
 # usbfadm
 
 Welcome to usbfadm.
 USB flash drive administration tool for FuguIta
 
   Version/Arch: 6.7/amd64  (FuguIta-6.7-amd64-202008111)
      Boot mode: manual
 Data stored in: not set
  Data Saved as: not set
 
 Type ? for help.
 
 ? : ? ->newdrive
Scanning USB devices after pressing ENTER.
 Please make sure the device inserted.
 Then press ENTER ->
Enter the device name of USB flash drive. ~
Contents of system log entries are displayed for your information;
 ==== disk(s) and vnode devices ============================
 sd0 at scsibus1 targ 0 lun 0: <VirtIO, Block Device, >
 sd0: 1024MB, 512 bytes/sector, 2097152 sectors
 sd1 at scsibus2 targ 0 lun 0: <VirtIO, Block Device, >
 sd1: 4096MB, 512 bytes/sector, 8388608 sectors
 vnd0: not in use
 vnd1: not in use
 vnd2: not in use
 vnd3: not in use
 vnd4: not in use
 vnd5: covering /sysmedia/fuguita-6.7-amd64.ffsimg on cd0a, inode 48172
Select the disk you will install FuguIta to
 Enter the name of device which FuguIta will be installed->sd1
There are several ways of boot. Choose one. ~
"Hybrid" enables boot with either Legacy BIOS or UEFI, but it's very difficult to change fdisk/GPT partition later.
 Select boot method:
   1: [Legacy BIOS]
   2:  UEFI
   3:  none (only for save data)
   4:  Hybrid
 ->1
Entering partition sizes. ~
If you answer "Y" for data encryption, input for passphrase will be prompted.
 Enter sizes for swap, user data and extra FAT.
   You can add suffix K, M, G or T (otherwise considered 'bytes').
   '*' implies 'all'
   '0' doesn't make this partition.
 
If you input any size of swap greater than 0, the maximum size of tmpfs can be expanded.
 3GB (3149MB) (6451136sectors) free
 swap->0
 
 3GB (3149MB) (6451136sectors) free
 user data->2560m
 
 user data encryption? [y/N] ->
 
 Create an extra FAT partition? [y/n] -> y
 
 target disk: sd1
   partition type=MBR
        boot type=Legacy
 -------------------- : ------
            partition :   size
 -------------------- : ------
           whole disk :    4GB
     partition tables :   32KB
          UEFI system :     0B
       FuguIta system : 9 46MB
         FuguIta swap :     0B
    FuguIta user data :    2GB
            MSDOS FAT :  589MB
 -------------------- : ------
 
 ***THIS IS THE LAST CHANCE***
 If you type 'Y' now, all the data on sd1 will be lost.
 Are you sure to modify disk sd1? [y/N] -> y
 
 ========================================
 = Clearing MBR, GPT and BSD disklabel
 =
 1+0 records in
 1+0 records out
 1048576 bytes transferred in 0.040 secs (25613268 bytes/sec)
 
 ...snip...
 
 /dev/rsd1d: 2560.0MB in 5242880 sectors of 512 bytes
 13 cylinder groups of 202.47MB, 12958 blocks, 25984 inodes each
 super-block backups (for fsck -b #) at:
  32, 414688, 829344, 1244000, 1658656, 2073312, 2487968, 2902624, 3317280,
  3731936, 4146592, 4561248, 4975904,
 ** /dev/rsd1d
 ** File system is already clean
 ** Last Mounted on /mnt
 ** Phase 1 - Check Blocks and Sizes
 ** Phase 2 - Check Pathnames
 ** Phase 3 - Check Connectivity
 ** Phase 4 - Check Reference Counts
 ** Phase 5 - Check Cyl groups
 3 files, 3 used, 1289388 free (20 frags, 161171 blocks, 0.0% fragmentation)
 
 ? : ? ->quit
 
 Bye bye...
 #
----
#topicpath
Top Index Search Recent Backups  Help  RSS